DSPIC30F2010-20I/SP

95,000 

Features

High-Performance Modified RISC CPU:
Modified Harvard architecture
C compiler optimized instruction set architecture
84 base instructions with flexible addressing modes
24-bit wide instructions, 16-bit wide data path
16 x 16-bit working register array
Up to 30 MIPs operation:
DC to 40 MHz external clock input
4 MHz-10 MHz oscillator input with PLL active (4x, 8x, 16x)
Peripheral and External interrupt sources
8 user selectable priority levels for each interrupt
4 processor exceptions and software traps
Primary and Alternate interrupt Vector TablesDSP Engine Features:
Modulo and Bit-Reversed Addressing modes
Two, 40-bit wide accumulators with optional saturation logic
17-bit x 17-bit single cycle hardware fractional/ integer multiplier
Single cycle Multiply-Accumulate (MAC) operation
40-stage Barrel Shifter
Dual data fetchPeripheral Features:
High current sink/source I/O pins: 25 mA/25 mA
Optionally pair up 16-bit timers into 32-bit timer modules
3-wire SPI™ modules (supports 4 Frame modes)
I2C™ module supports Multi-Master/Slave mode and 7-bit/10-bit addressing
Addressable UART modules with FIFO buffersMotor Control PWM Module Features:
Complementary or Independent Output modes
Edge and Center Aligned modes
Multiple duty cycle generators
Dedicated time base with 4 modes
Programmable output polarityDead time control for Complementary mode
Manual output control
Trigger for synchronized A/D conversionsQuadrature Encoder Interface Module Features:
Phase A, Phase B and Index Pulse input
16-bit up/down position counter
Count direction status
Position Measurement (x2 and x4) mode
Programmable digital noise filters on inputs
Alternate 16-bit Timer/Counter mode
Interrupt on position counter rollover/underflowAnalog Features:
10-bit 1 Msps Analog-to-Digital Converter (A/D)
A/D Conversion available during Sleep and Idle
4 Sample/Hold Channels
Multiple Conversion Sequencing OptionsSpecial Microcontroller Features:
Enhanced Flash program memory:
10,000 erase/write cycle (min.) for industrial temperature range, 100K (typical)
Data EEPROM memory:
100,000 erase/write cycle (min.) for industrial temperature range, 1M (typical)
Self-reprogrammable under software control
Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)
Flexible Watchdog Timer (WDT) with on-chip low power RC oscillator for reliable operation
Fail-Safe clock monitor operation
Detects clock failure and switches to on-chip low power RC oscillator
Programmable code protection
In-Circuit Serial Programming™ (ICSP™)
Programmable Brown-out Detection and Reset generation
Selectable Power Management modes
Sleep, Idle and Alternate Clock modesCMOS Technology:
Low power, high speed Flash technology
Wide operating voltage range (2.5V to 5.5V)
Industrial and Extended temperature ranges
Low power consumption
 Parameter Name
 Value
Architecture
16-bit
CPU Speed (MIPS)
30
Memory Type
Flash
Program Memory (KB)
12
RAM Bytes
512
Temperature Range C
-40 to +85
Operating Voltage Range (V)
2.5 to 5.5
I/O Pins
20
Pin Count
28
System Management Features
BOR, LVD
POR
Yes
WDT
Yes
Internal Oscillator
7.37 MHz, 512 kHz
nanoWatt Features
Fast Wake/Fast Control
Digital Communication Peripherals
1-UART
1-SPI
1-I2C
Analog Peripherals
1-A/D 6×10-bit @ 1000(ksps)
Capture/Compare/PWM Peripherals
4/2
PWM Resolution bits
16
Motor Control PWM Channels
6
Quadrature Encoder Interface (QEI)
1
Timers
3 x 16-bit 1 x 32-bit
Parallel Port
GPIO
datasheet