DSPIC30F3012-30I/SO

99,000 

  

 
dsPIC30F Sensor Family 16-bit Digital Signal Controller
Parameter Name
 Value
 Architecture
 16-bit
 CPU Speed (MIPS)
 30
 Memory Type
 Flash
 Program Memory (KB)
 24
 RAM Bytes
 2,048
 Temperature Range C
 -40 to 125
 Operating Voltage Range (V)
 2.5 to 5.5
 I/O Pins
 12
 Pin Count
 18
 System Management Features
 PBOR, LVD
 POR
 Yes
 WDT
 Yes
 Internal Oscillator
 7.37 MHz, 512 kHz
 nanoWatt Features
 Fast Wake/Fast Control
 Digital Communication Peripherals
 1-UART, 1-SPI, 1-I2C
 Analog Peripherals
 1-A/D 8×12-bit @ 200(ksps)
 Timers
 3 x 16-bit 1 x 32-bit
 Parallel Port
 GPIO
Features
High-Performance Modified RISC CPU:
 Modified Harvard architecture
 C compiler optimized instruction set architecture
 84 base instructions with flexible addressing modes
 24-bit wide instructions, 16-bit wide data path
 16 x 16-bit working register array
 Up to 30 MIPs operation:
            – DC to 40 MHz external clock input
            – Internal FRC input with PLL active (4x, 8x, 16x)
            – 4 MHz-10 MHz oscillator input with PLL active (4x, 8x, 16x)
            – 10 MHz – 20 MHz oscillator input in HS/2 or HS/3 with PLL active (4x, 8x, 16x)
 Peripheral and External interrupt sources
 8 user selectable priority levels for each interrupt
 4 processor exceptions and software traps
 Primary and Alternate interrupt Vector Tables
DSP Engine Features:
 Modulo and Bit-Reversed Addressing modes
 Two, 40-bit wide accumulators with optional saturation logic
 17-bit x 17-bit single cycle hardware fractional/ integer multiplier
 Single cycle Multiply-Accumulate (MAC) operation
 40-stage Barrel Shifter
 Dual data fetch
Peripheral Features:
 High current sink/source I/O pins: 25 mA/25 mA
 Optionally pair up 16-bit timers into 32-bit timer modules
 3-wire SPI™ modules (supports 4 Frame modes)
 I2C™ module supports Multi-Master/Slave mode and 7-bit/10-bit addressing
 Addressable UART modules with FIFO buffers and selectable pins
Analog Features:
 12-bit 200 Ksps Analog-to-Digital Converter (A/D)
 A/D Conversion available during Sleep and Idle
 1 Sample/Hold
 Multiple Conversion Sequencing Options
Special Microcontroller Features:
 Enhanced Flash program memory:
            – 10,000 erase/write cycle (min.) for industrial temperature range, 100K (typical)
 Data EEPROM memory:
            – 100,000 erase/write cycle (min.) for industrial temperature range, 1M (typical)
 Self-reprogrammable under software control
 Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)
 Flexible Watchdog Timer (WDT) with on-chip low power RC oscillator for reliable operation
 Fail-Safe clock monitor operation
 Detects clock failure and switches to on-chip low power RC oscillator
 Programmable code protection
 In-Circuit Serial Programming™ (ICSP™)
 Programmable Brown-out Detection and Reset generation
 Selectable Power Management modes
            – Sleep, Idle and Alternate Clock modes
           
CMOS Technology:
 Low power, high speed Flash technology
 Wide operating voltage range (2.5V to 5.5V)
 Industrial and Extended temperature ranges
 Low power consumptiondsPIC30F2011/2012/3012/3013 Data Sheet

Danh mục: