DSPIC33FJ12MC201-I/P

86,229 

 Features:
Operating Range:
DC – 40 MIPS (40 MIPS at 3.0-3.6V, -40°C to +85°C)
Industrial temperature range (-40°C to +85°C)
Extended temperature range (-40°C to +125°C)
High-Performance DSC CPU:
Modified Harvard architecture
C compiler optimized instruction set
16-bit wide data path
24-bit wide instructions
Linear program memory addressing up to 4M instruction words
Linear data memory addressing up to 64 Kbytes
83 base instructions: mostly 1 word/1 cycle
Two 40-bit accumulators with rounding and saturation options
Flexible and powerful addressing modes:
Indirect
Modulo
Bit-Reversed
Software stack
16 x 16 fractional/integer multiply operations
32/16 and 16/16 divide operations
Single-cycle multiply and accumulate:
Accumulator write back for DSP operations
Dual data fetch
Up to ±16-bit shifts for up to 40-bit data Timers/Capture/Compare/PWM:
Timer/Counters, up to three 16-bit timers
Can pair up to make one 32-bit timer
1 timer runs as Real-Time Clock with external 32.768 kHz oscillator
Programmable prescaler
Input Capture (up to 4 channels):
Capture on up, down or both edges
16-bit capture input functions
4-deep FIFO on each capture
Output Compare (up to 2 channels):
Single or Dual 16-Bit Compare mode
16-bit Glitchless PWM mode
Interrupt Controller:
5-cycle latency
118 interrupt vectors
Up to 26 available interrupt sources
Up to 3 external interrupts
7 programmable priority levels
4 processor exceptions
Digital I/O:
Peripheral pin Select functionality
Up to 21 programmable digital I/O pins
Wake-up/Interrupt-on-Change for up to 21 pins
Output pins can drive from 3.0V to 3.6V
Up to 5V with output drain configuration
All digital input pins are 5V tolerant
4 mA sink on all I/O pins
On-Chip Flash and SRAM:
Flash program memory, up to 12 Kbytes
Data SRAM, up to 1 Kbyte
Boot and General Security for Program Flash
System Management:
Flexible clock options:
External, crystal, resonator, internal RC
Fully integrated Phase-Locked Loop (PLL)
Extremely low jitter PLL
Power-up Timer
Oscillator Start-up Timer/Stabilizer
Watchdog Timer with its own RC oscillator
Fail-Safe Clock Monitor
Reset by multiple sources
Power Management:
On-chip 2.5V voltage regulator
Switch between clock sources in real time
Idle, Sleep and Doze modes with fast wake-up
Motor Control Peripherals:
6-channel 16-bit Motor Control PWM
3 duty cycle generators
Independent or Complementary mode
Programmable dead time and output polarity
Edge-aligned or center-aligned
Manual output override control
1 Fault input
Trigger for ADC conversions
PWM frequency for 16-bit resolution (@ 40 MIPS) = 1220 Hz for Edge-Aligned mode, 610 Hz for Center-Aligned mode
PWM frequency for 11-bit resolution (@ 40 MIPS) = 39.1 kHz for Edge-Aligned mode, 19.55 kHz for Center-Aligned mode
2-channel 16-bit Motor Control PWM
1 duty cycle generator
Independent or Complementary mode
Programmable dead time and output polarity
Edge-aligned or center-aligned
Manual output override control
1 Fault input
Trigger for ADC conversions
PWM frequency for 16-bit resolution (@ 40 MIPS) = 1220 Hz for Edge-Aligned mode, 610 Hz for Center-Aligned mode
PWM frequency for 11-bit resolution (@ 40 MIPS) = 39.1 kHz for Edge-Aligned mode, 19.55 kHz for Center-Aligned mode
Quadrature Encoder Interface module:
Phase A, Phase B and index pulse input
16-bit up/down position counter
Count direction status
Position Measurement (x2 and x4) mode
Programmable digital noise filters on inputs
Alternate 16-bit Timer/Counter mode
Interrupt on position counter rollover/underflow
Analog-to-Digital Converters (ADCs):
10-bit, 1.1 Msps or 12-bit, 500 Ksps conversion:
2 and 4 simultaneous samples
Up to 6 input channels with auto-scanning
Conversion start can be manual or synchronized with 1 of 4 trigger sources
Conversion possible in Sleep mode
±2 LSb max integral nonlinearity
±1 LSb max differential nonlinearity
CMOS Flash Technology:
Low-power, high-speed Flash technology
Fully static design
3.3V (±10%) operating voltage
Industrial temperature
Low-power consumption
Communication Modules:
4-wire SPI
Framing supports I/O interface to simple codecs
Supports 8-bit and 16-bit data
Supports all serial clock formats and sampling modes
I2C™
Full Multi-Master Slave mode support
7-bit and 10-bit addressing
Bus collision detection and arbitrationParameter Name
 Value
Architecture
16-bit
CPU Speed (MIPS)
40
Memory Type
Flash
Program Memory (KB)
12
RAM Bytes
1,024
Temperature Range C
-40 to +85
Operating Voltage Range (V)
3 to 3.6
I/O Pins
15
Pin Count
20
System Management Features
BOR
POR
Yes
WDT
Yes
Internal Oscillator
7.37 MHz, 32.768 kHz
nanoWatt Features
Fast Wake/Fast Control
Digital Communication Peripherals
1-UART
1-SPI
1-I2C
Analog Peripherals
1-A/D 4×12-bit @ 500(ksps)
Capture/Compare/PWM Peripherals
4/2
PWM Resolution bits
16
Motor Control PWM Channels
8
Quadrature Encoder Interface (QEI)
1
Timers
3 x 16-bit 1 x 32-bit
Parallel Port
GPIO
Cap Touch Channels
4
datasheet
 
 

 

Danh mục: