PIC24HJ256GP206A-I/PT

143,000 

  PIC24HJXXXGPX06A/X08A/X10A Data Sheet (03/29/2011)
 
PIC24HJXXXGPXXXA 16-bit General Purpose Microcontroller with seamless migration options from/to PIC24F, dsPIC30F and dsPIC33F devices. These devices are avialble with Extended temperature options
Parameter Name
 Value
 Architecture
 16-bit
 CPU Speed (MIPS)
 40
 Memory Type
 Flash
 Program Memory (KB)
 256
 RAM Bytes
 16,384
 Temperature Range C
 -40 to 125
 Operating Voltage Range (V)
 3 to 3.6
 I/O Pins
 53
 Pin Count
 64
 System Management Features
 PBOR
 POR
 Yes
 WDT
 Yes
 Internal Oscillator
 7.37 MHz, 512 kHz
 nanoWatt Features
 Fast Wake/Fast Control
 Digital Communication Peripherals
 2-UART, 2-SPI, 2-I2C
 Codec Interface
 NO
 Analog Peripherals
 1-A/D 18×12-bit @ 500(ksps)
 Capture/Compare/PWM Peripherals
 8/8
 PWM Resolution bits
 16
 Timers
 9 x 16-bit 4 x 32-bit
 Parallel Port
 GPIO
 Hardware RTCC
 No
 DMA
 8
 XLP
 NO
  Features
Operating Range:
•   DC – 40 MIPS (40 MIPS @ 3.0-3.6V, -40°C to +125°C)
•   Industrial temperature range (-40°C to +85°C)
•   Extended temperature range (-40°C to +125°C)High-Performance  CPU: Modified Harvard architecture
•   C compiler optimized instruction set
•   16-bit wide data path
•   24-bit wide instructions
•   Linear program memory addressing up to 4M instruction words
•   Linear data memory addressing up to 64 Kbytes
•   71 base instructions: mostly 1 word/1 cycle
•   Sixteen 16-bit General Purpose Registers
•   Flexible and powerful Indirect Addressing modes
•   Software stack
•   16 x 16 multiply operations
•   32/16 and 16/16 divide operations
•   Up to ±16-bit data shifts. Direct Memory Access (DMA):  8-channel hardware DMA
•   2 Kbytes dual ported DMA buffer area (DMA RAM) to store data transferred via DMA:
– Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing)
•   Most peripherals support DMA. Interrupt Controller:  5-cycle latency
•   118 interrupt vectors
•   Up to 61 available interrupt sources
•   Up to 5 external interrupts
•   7 programmable priority levels
•   5 processor exceptions
Digital I/O:
 •   Wake-up/Interrupt-on-Change on up to 24 pins
•   Output pins can drive from 3.0V to 3.6V
•   All digital input pins are 5V tolerant
•   4 mA sink on all I/O pins
 System Management:
 •   Flexible clock options:
– External, crystal, resonator, internal RC
– Fully integrated PLL
– Extremely low jitter PLL
•   Power-up Timer
•   Oscillator Start-up Timer/Stabilizer
•   Watchdog Timer with its own RC oscillator
•   Fail-Safe Clock Monitor
•   Reset by multiple sources
 Power Management:
 •   On-chip 2.5V voltage regulator
•   Switch between clock sources in real time
•   Idle, Sleep and Doze modes with fast wake-up
 Timers/Capture/Compare/PWM:
 •   Timer/Counters, up to nine 16-bit timers:
– Can pair up to make four 32-bit timers
– 1 timer runs as Real-Time Clock with external 32.768 kHz oscillator
– Programmable prescaler
•   Input Capture (up to 8 channels):
– Capture on up, down or both edges
– 16-bit capture input functions
– 4-deep FIFO on each capture
•   Output Compare (up to 8 channels):
– Single or Dual 16-Bit Compare mode
– 16-bit Glitchless PWM mode
 Communication Modules:
 •   3-wire SPI (up to 2 modules):
– Framing supports I/O interface to simple codecs
– Supports 8-bit and 16-bit data
– Supports all serial clock formats and sampling modes
•   I2C™ (up to 2 modules):
– Full Multi-Master Slave mode support
– 7-bit and 10-bit addressing
– Bus collision detection and arbitration
– Integrated signal conditioning
– Slave address masking
•   UART (up to 2 modules):
– Interrupt on address bit detect
– Interrupt on UART error
– Wake-up on Start bit from Sleep mode
– 4-character TX and RX FIFO buffers
– LIN bus support
– IrDA® encoding and decoding in hardware
– High-Speed Baud mode
– Hardware Flow Control with CTS and RTS
•   Enhanced CAN (ECAN™ module) 2.0B active (up to 2 modules):
– Up to 8 transmit and up to 32 receive buffers
– 16 receive filters and 3 masks
– Loopback, Listen Only and Listen All Messages modes for diagnostics and bus monitoring
– Wake-up on CAN message
– Automatic processing of Remote Transmission Requests
– FIFO mode using DMA
– DeviceNet™ addressing support. Analog-to-Digital Converters:
 •   Up to two A/D modules in a device
•   10-bit, 1.1 Msps or 12-bit, 500 ksps conversion:
– 2, 4 or 8 simultaneous samples
– Up to 32 input channels with auto-scanning
– Conversion start can be manual or synchronized with 1 of 4 trigger sources
– Conversion possible in Sleep mode
– ±2 LSb max integral nonlinearity
– ±1 LSb max differential nonlinearity
 CMOS Flash Technology:
 •   Low-power, high-speed Flash technology
•   Fully static design
•   3.3V (±10%) operating voltage
•   Industrial temperature
•   Extended temperature
•   Low-power consumption.  
PIC24HJXXXGPX06A/X08A/X10A Data Sheet
 

 

Danh mục: